Atlant washing machine - error f4

Any modern washing machine is equipped with a self-diagnosis and control system for problems in the device. To simplify the task - both users and employees of special service departments, manufacturers of various equipment enter error codes - they usually have a alphanumeric designation. So, if you have an Atlant washing machine, an F4 error indicates problems with the drain pump. You will learn more about this problem and other error codes for the technology of this brand from this article.

to contents ↑

Decoding error codes

Decryption will occur according to this scheme:

1. Error code.
2. His transcript.
3. Fault Options
4. Ways to fix this problem.

to contents ↑

Sel

If on a machine that does not have a display, the indicators do not light up, this means that the selector of the interface module has malfunctioned. The Sel code on a typewriter with a display will also testify to this.

Most likely, there was a breakdown of the potentiometer, which is needed in order to select programs. Replace the control interface module.

to contents ↑

None

The display shows the code None. If there is no display, absolutely all indicators light up. This code means that the amount of foam that has been produced is excessive.

What could lead to this problem:

• Too much powder was used during washing. Just limit yourself to less powder.

Important! In order to continue to rule out such a problem, check out our separate article once and remember all the recommendations contained in it as to which automatic machine andhow much powder to pour.

• Invalid mode set. That is, the regime that foresees the flooding of a large amount of water. Choose a washing mode that is specifically designed for a specific type of fabric.
• Used such a powder or any other detergent that is not suitable for washing in a machine.

Important! Use only powders and detergents that are suitable for washing with this machine. Read a helpful review about this, which will also help you take better care of your things - “Which is better - gel or detergent powder?”.

to contents ↑

Display F2

If there is no display, the third diode will light. This error code of the Atlant washing machine means that the temperature sensor has failed:

• There may be a problem with the contacts and wiring of the temperature sensor or the module. Make sure that the contacts and wires are fully functional.
• The temperature sensor has deteriorated. Our instructions from a special article will help you here, as you need replacement of TEN.
• Out of order control module. Replace this faulty module.

to contents ↑

F3 is lit on the panel

On the older model, the 4th and 3rd indicators light up. The heating element of your washer is out of order. This is possible for the following reasons:

• The heating element has broken. Replace the heating element.
• Violation of wiring or contacts. Make sure that the wires and contacts are in good condition.
• The control module has failed. Replace the module.

to contents ↑

Display F4

Alternatively, if the Atlant washing machine generates an error f4 - diode number 2 is on. Damage to the drain pump, it's a pump.

Causes:

• The drain hose is pinched or clogged. Straighten the hose, find and remove the blockage.
• Incorrect hose installation. Reinstall the hose as instructed.
• If a foreign object gets inside the pump, its impellers are stalled. Eliminate the trapped object, check the impeller for rotation.
• The drain pump is broken. Replace a broken pump.
• The ball in the drain sleeve has sunk. Drain the washing machine using a tube, and then change the coupling.
• Clogged drain coupling. Perform cleaning.
• With wiring and contact problems. Check them for serviceability.
• The electronics module has become unusable. Replace the electronics module.

to contents ↑

The display lights up F5

On the non-display machine, the 2nd and 4th indicators light up. Damage to the bay valve.

Causes:

• Clogged water inlet filter. Clean filter.
• Clogged or pinched inlet hose. Unscrew the hose from the machine, let the water run for inspection. If necessary, clean the hose.
• There is no water in the water supply, the water supply in the tap itself is closed, or the filling valve is broken. Make sure your faucet is open. Make sure that the water in the water supply is not disconnected. If necessary, replace the valve.
• The circuit between the filler valve and the control module is broken. Using a tester, check for the presence or absence of an open.
• Faulty contact valve. Check the contacts and make sure they are operational.
• Damage to the control module. Replace it with a new one.

to contents ↑

The control panel issued F6

If there is no display, the 2nd and 3rd indicators will light up. Problem with electric motor relay.

The reason is that the stator winding is overheated. The contacts that are responsible for the thermal safety of the engine are disconnected. Replace the unit engine.

Important! Keep in mind that replacing a motor is usually cheaper for a price than buying new equipment. To assess the appropriateness of your decision, learn all about repair of electric motors of washing machines.

to contents ↑

Display F7

In the older model of the Atlant washing machine, the 2nd, 3rd, 4th indicators light up. The problem is the power supply.

Causes:

• Damage to the interference filter. In this case, you just need to change it.
• The mains voltage does not correspond to the necessary - it can be voltage more or less. Check the network with a tester.
• The control module has broken. Replace it.

to contents ↑

Error Code F8

Alternative - indicator number 1 is on. Too much water in the tank.

Causes:

• The pressure switch broke. Replace it.
• The filler valve has stalled. Replace the old valve.
• Problems with contacts or wiring of the pressure switch, as well as the control module. Check these wires and contacts for breaks.
• Leakproof cylinder. Check your tank.
• The control module has broken. Replace it with one that is working.

to contents ↑

F9 lock

The indicators under number 1 and number 4 are on. Such error codes of the Atlant washing machine mean that problems lie in the tachometer engine.

Causes:

• Malfunction of contacts and wires of the control module or electric motor. Make sure there are no or presence of malfunctions, having checked all contacts and wires.
• The tachogenerator or engine has broken. Replace engine.

to contents ↑

Display F10

If your car without a display, indicator number 1 and number 3 are on. UBL broke - door lock.

Possible problems with this error code of the Atlant washing machine:

• Fault with lock. Replace it with a brand new one.
• The control module has broken. Replace.

to contents ↑

The display shows “door”

The 1st, 3rd, 4th indicator will light up. Most likely the castle broke.

What to do:

• Missing contact lock. Make sure that all wires are connected correctly and breaks are excluded.
• The hatch is not tightly closed enough. Close the hatch again.
• Skewed lock or door. Fix the hatch or lock.
• The circuit between the control module and the sunroof interlock was broken. Use a tester to test the circuit.
• Problems with the lock slot. Check if the wires are connected correctly and are intact.

to contents ↑

Display F12

The 1st and 2nd indicators should light up. It is possible breakdown of the triath of the engine.

What caused:

• The engine of the machine itself broke down. Replace it.
• The motor winding was cut off. Replace motor.
• No contact. Check the condition of the connector and wires.

to contents ↑

Display F13

In this case, the 1st, 2nd, 4th indicators will light. The difficulty with this error code of the Atlant washing machine is that there is no single reason for the breakdown.

Usually these are problems with contacts or wiring. Check wires and contacts.

to contents ↑

Display F14

The 1st and 2nd indicators will start emitting light. A program error has occurred.

There was a program crash due to incorrect programming of the electronics module. Replace this module urgently.

to contents ↑

Display F15

This error code of the Atlant washing machine indicates that a water leak has been detected. The reasons for this phenomenon:

• The tank was depressurized. Replace it.
• Flowing through a locked door. Replace the manhole cuff.
• Sealing of the drain hose, drain coupling, nozzles is broken. Try to locate the leak and then repair it. Make sure that the clamps are tight enough to fix the nozzles, and the nozzles and the drain hose are intact.

to contents ↑

Stock footage

In this article, we reviewed the most common error codes for Atlant washing machines - with and without a display, so you can figure out what the causes of the breakdown are. Remember that replacing the engine is a very expensive pleasure, repair of the electronic control board is carried out only by masters of special qualifications. But to deal with the drain pump, pump, sunroof, for example, if the Atlant washing machine generated an F4 error or the Door code, you can probably do it yourself.