Soda and vinegar from a sewage blockage

If you notice that the water from the sink or bath doesn’t drain well, take action immediately. The simplest thing you can do is call a plumber who professionally cleans the pipes. The second solution to this problem is to tackle the blockage yourself. With this approach, soda + vinegar will help you.

to contents ↑

Causes of blockages in the sewer

There are several main reasons that contribute to disruption of the normal operation of the sewage system, as a result of which regular cleaning of pipes with soda and vinegar becomes necessary:

• Incorrect pipe installation. Violation of the rules for installing pipes, their incorrect slope or the use of cement mortar during the installation of the toilet bowl causes frequent garbage clogging in sewer pipes.
• Non-compliance with the rules for the use of plumbing fixtures. The discharge of large foreign objects into sewers is one of the reasons for the malfunctioning of such systems.
• Thick growth on the inner walls of the pipeline. It arises from a long service life.
• Incorrect cleaning of sewage drains or its complete absence.

Important! Almost every one of us at least once in our lives has been faced with the problem of clogged sewers. This not only brings inconvenience to the life of the residents of the house, but also becomes a threat to more serious problems. Clogged sewage can cause damage to pipes and as a result - damage to the repair of their own and neighboring apartments.

In order to timely clean the pipes yourself, it is not necessary to buy expensive chemicals. Ordinary soda, vinegar, which is in every house, can help with this.

to contents ↑

In what places is blockage most common?

Most often the following sections of sewer pipes are clogged:

1. Sewer pipe of a kitchen sink. Due to the constant subsidence of fat, this section of the pipeline easily accumulates debris, which becomes the reason for poor drainage.

Important! To minimize the risk of clogging, it is recommended to use strainers in kitchen sinks that will not allow most of the debris to enter sewers.

2. Bathroom drain pipe. This area is most often clogged due to the large amount of hair.
3. Flushing the toilet. This site is clogged less often than others, since it initially goes wider in diameter. And only in violation of the elementary rules for the use of this plumbing, a serious blockage of the sewer occurs.

Important! In no case should you throw baby diapers, rags, feminine hygiene products, construction waste and plastic bags into the toilet drain.

If the problem still arises, then you should quickly take up its resolution.

Important! If the water has completely ceased to go into the sewer, and you do not have the experience of self-cleaning pipes, then you should seek the help of specialists. It is unlikely that the first time you can independently eliminate a serious blockage. If the sewage system still works, but not so efficiently, it is quite possible to clean the pipes yourself with soda and vinegar.

to contents ↑

Methods for self-cleaning sewer pipes

Before starting any action, the location of the blockage should be determined.To do this, check the operation of all the drains in the house:

1. If the drain works perfectly in all plumbing fixtures, except for one, then the blockage is local and removing it is not difficult.
2. If problems are visible in all drains at the same time, then the blockage is global and more serious measures will be required to remove it.

Flushing pipes with boiling water

Kitchen sewers are often clogged with grease. To remove small body fat, pour the drain with boiling water.

Important! You can’t clean difficult blockages in this way, but to prevent them by regularly washing pipes with boiling water is quite possible.

Pipe cleaning with soda and vinegar

The neutralization reaction between acid and alkali will help to remove debris in the pipes. Concentrated solutions can cause significant damage to the sewer pipe, but ordinary soda and vinegar will clean the sink without consequences. To do this, proceed as follows:

1. Pour a glass of soda into the problematic drain hole.
2. Send the same glass of vinegar.
3. Cover the drain with a piece of cloth or a special plug so that the reaction foam does not come out.
4. Do not use this drain for about half an hour, so that the reaction between soda and vinegar completely takes place.
5. After the time has elapsed, turn on the hot water and rinse the sewer pipe well in this way.

How to clean pipes with soda?

Soda without impurities is also able to remove small blockages in the sewer:

• Clean the drain hole with a plunger or fill with boiling water and leave for 15 minutes.
• Mix a glass of soda with 3 cups of boiling water and pour the resulting mixture into the drain hole.
• Wait 15-20 minutes and empty clean tap water to remove any remaining dirt and cleaning agent from the sewer.

How to clean the blockage with soda and salt?

Soda can also be mixed with salt and thus flush out pipes from unwanted debris. This method is best done in the evening, or rather at night, so that no one uses the sink for a long time.

The principle of use:

1. Mix half a glass of soda and the same amount of salt.
2. Pour the resulting mixture into the drain hole.
3. Pour boiling water over the pipe and leave for 8-10 hours.

Cleaning the sewer using special household chemicals

Plastic sewer pipes will quickly and efficiently help clean up special household cleaning products. A plumbing cable is absolutely not suitable for cleaning this type of pipe, since it can damage their walls, but special-purpose household chemicals or soda and vinegar for cleaning pipes are the most effective means.

A large selection of household cleaning products in stores will facilitate your purchase. Using any of them, clearly follow the instructions on the packaging.

Important! To avoid serious problems with obstruction of sewer pipes, it is necessary to carry out regular preventive cleaning of drains, at least once every 2-3 months, by any means you choose.

Using a plunger to clean the sewer

A plunger is a fixture that should be in every home. Using it is quite simple and does not require much skill:

1. Install the plunger so that the drain hole in the sink is completely covered by its bowl.
2. Draw a small amount of water into the sink and start moving the plunger handle up and down.
3. After 15-20 movements with the handle, pull the plunger up sharply. If the accumulated water quickly went into the drain hole, then the blockage was removed, and you coped with it perfectly. If the water leaves slowly, then it is worth repeating the whole procedure first.

Plumbing cable - an assistant in the removal of sewage blockages

This device is a tool for professional plumbers. To clean the sewer with a cable, two people are required to act in this way:

• First you need to find the entrance to the pipe. To do this, remove the sink siphon.
• One participant in the process will twist the handle, the other - to advance the cable through the pipe.
• After finishing work, rinse the drain with plenty of water.

to contents ↑

Stock footage

If none of the above methods for self-cleaning sewer pipes helped, then seek help from professionals. Using special equipment, they quickly and efficiently remove obstruction in the sewage system by hydrodynamic cleaning.