Mold on the slopes of plastic windows

Mold on the slopes of plastic windows is a serious problem that worries many owners of such windows after a certain period of their operation. Such designs are very convenient to use, protect our home from cold and noise, and they require minimal maintenance - they do not need to be painted and washed inside each time. But with improper installation, over time, such a nuisance as mold on plastic windows can appear. How to deal with it, you will learn from this article.

to contents ↑

Where does mold on plastic come from?

Mold is a type of fungus that infects and quickly destroys the surface.

The causes of the appearance of the fungus may be as follows:

1. High humidity.
2. High temperature: +20 and above.
3. Poor ventilation.
4. Incorrect installation.

Important! For our health, mold on windows is a destructive effect. It can lead to both allergies and other diseases, even death.

to contents ↑

How to deal with mold on the windows?

The fungus on the plastic windows can be removed with bleach, ammonia or any means for cleaning various surfaces. But remember, acting by such methods, it is unlikely that mold will go away forever. It is highly likely that it will appear back at any opportunity. Therefore, it is necessary to deal with it comprehensively, that is, stage by stage to carry out cleaning, surface treatment of plastic and fix the result.

to contents ↑

Cleaning

It is the slopes that are the focus of mold growth. Therefore, in order to get rid of the problem, do the following:

1. Remove a decorative facing of slopes.
2. Sanitize the walls.

Important! If the slopes are finished with drywall, it is best to replace it, because in this case, most likely the mold on the slopes has already penetrated deep into the material.

3. Take a stiff brush and remove any signs of mold.
4. Make a solution of household bleach and water in a ratio of 1: 5 and treat the problem area.

Important! Before you process surfaces, wear rubber gloves.

5. Ventilate the room after the procedure.

to contents ↑

Antifungal slope treatment

The tool can be bought either already finished, or in the form of components, of which you will prepare the mixture at home. The finished mixture is based on chlorine, and also contains various additives. A more gentle option is based on copper sulfate.

Remedies for fungus at home:

1. Acetic acid 70% - 0.2 liters. Boric acid - 0.2 liters. Water - 1 liter.
2. Sodium fluoride - 0.1 liters. Copper sulfate - 0.1 liters. Water - 1 liter.
3. Copper sulfate - 0.1 liters. Household bleach - 0.1 liters. Water - 1 liter.

Important! Ingredients such as sodium fluoride and copper sulfate are sold in hardware stores. Copper sulfate is applied to the entire area of ​​the slopes with a synthetic brush. And do not forget to wear rubber gloves and a respiratory mask. After the plastic windows have been treated against mold, it is necessary to carefully ventilate the room.

to contents ↑

Result fixing

In order for the fungus to no longer appear on plastic windows, it is necessary to use waterproofing agents. An excellent option is a rubber-based mastic or primer.

to contents ↑

Prevention Rules:

1. Do not block the ventilation grill in the kitchen.
2. Check the condition of the plastic windows: sealing, condition of frames and slopes, serviceability of mechanisms.
3. Do not put many flowers on the windowsill. They increase humidity, and create conditions for the propagation of the fungus.
4. Do not close the doors to rooms to let in air.
5. Pay attention to plumbing, keep it in good condition.
6. Ventilate the room.
7. Do not dry laundry on batteries or with windows closed.

to contents ↑

Stock footage

How to deal with mold on the windows? Now this question will not panic you, as you have a clear plan of action. The main thing is to do all the procedures in a complex and then you will get rid of it very soon. Use the tips above and the fungus will no longer bother you.