How to Clean a Vanish Carpet

Carpet - the most affected by pollution in the house, there are traces of not only dust, but also household stains. Therefore, every housewife is puzzled by the question: how to get rid of dirt on the carpet? With the help of modern household chemicals, you can remove the most difficult traces, and in this article we will look at how to clean the carpet at home with Vanish.

to contents ↑

What is Vanish?

Vanish is a universal cleaner for removing stains of any origin and from almost all types of coatings, in our case, carpet. It is available in the form of shampoo or powder.

You can use it on any floor coverings - rugs, with the usual and even long pile, in light and colored. It is due to such a wide spectrum of action combined with great efficiency that this cleanser is so popular.

to contents ↑

How to wash a Vanish carpet?

To get the expected result and at the same time not to spend a lot of effort, consider the following recommendations during the cleaning process:

1. It is best to start removing dust from the inside of the carpet so that it does not drive into the surface.
2. Collect all the dirt under the cover, vacuum the wrong side, and then the front, fleecy.
3. Remove stains with a cleanser, starting from the edges moving towards the middle.
4. Do not rub the dirt, in order to prevent its spread.
5. Collect the remnants of the product along the pile, so as not to destroy the structure of the coating.
6. Do not over-moisten the carpet with a cleaner, as its base may not completely dry out and will begin to rot, giving off unpleasant odors.
7. Dry the carpet thoroughly after wet cleaning: turn it upside down until it is completely dry.

to contents ↑

How to clean the carpet Vanish?

Before you clean the carpet at home Vanish, prepare the necessary inventory:

• foam sponge;
• soft or medium hard brush;
• pure white moisture-absorbing rag;
• a vacuum cleaner;
• latex gloves.

Next, use the step-by-step procedure to clean the carpet with Vanish cleaner.

Stage 1 - Carpet Pre-Cleaning

Remove dust and large debris from the carpet in the way convenient for you: vacuum up, if possible, it is better to knock it out on the street. This will prevent excess stains.

Stage 2 - Preparation of the cleaning agent

1. Dissolve the cleaning agent in warm water at a ratio of 1: 9.
2. Beat the shampoo until a cool foam forms.

Important! Since the foam is just a cleaning agent, whisk it thoroughly, the cleanliness of the carpet will depend on this..

Stage 3 - Cleaning Methods

1. Cleaning the carpet with a vacuum cleaner:
   1. Spread Vanish Oxi Action Powder onto the carpet.
   2. Soak for 30 minutes.
2. If you clean the carpet by hand:
   1. Put foam on a sponge or brush, apply on the coating.
   2. Spread the product evenly over the surface to be cleaned.
   3. Rub the substance in a circular motion.
   4. Leave for 1-2 hours depending on the degree of contamination.

Important! Follow these guidelines to help prevent re-contamination of your carpet while it is being cleaned by Vanish.:

• In order for the carpet to not shrink, try not to over-moisten it.
• During cleaning, do not walk on the surface to be treated, since at this time the product reacts with dirt.
• To remove old stains on the carpet for contamination, apply a little concentrate in a few minutes without spreading it, this will greatly facilitate the cleaning task.

Stage 4 - Interaction with pollution

The drying time of the foam depends on the type of material and the hairiness of the coating. Closely monitor the reaction of the action.

Stage 5 - Final Procedure

1. Vacuum the remnants of the product.
2. To prevent dust from spreading over the carpet, do not press on the brush.
3. Collect foam or powder in one direction along the pile.
4. Dry the carpet well before using it again.

Important! Do not use a loop brush for carpets, do foam cleaning and clean it by hand with a damp cloth. In this case, the pile dries out with difficulty, and subsequently there is an unpleasant odor and mold.

to contents ↑

How to clean a carpet with a vanish?

If your carpet is made of natural materials - categorically do not use a washing vacuum cleaner or other type of wet cleaning.

The Vanish universal cleaner is suitable for cleaning mixed or artificial fibers: it moisturizes slightly, does not penetrate deeply, but the foam itself effectively removes even the most old dirt.

Important! Use the carpet cleaning method described above to remove dirt from the carpet. A prerequisite for the long existence of carpet is thorough drying.

to contents ↑

Useful Tips

• To keep the floor clean, vacuum it 1-2 times a week.
• When using a chemical reagent, test it in an inconspicuous area of ​​the workpiece.
• Any cleaning agent is most effective if used immediately after contamination.
• Please note that Vanish Oxi Action is not suitable for cleaning natural fiber carpets.
• Work in a well-ventilated area.
• Wash Vanish thoroughly to avoid allergic reactions.

to contents ↑

Stock footage

Now you are sure that you have made the right choice when buying Vanish for carpet cleaning. Use it clearly according to the instructions and you will definitely get a high-quality result in the shortest possible time. Further - it remains only to enjoy the cleanliness and comfort of your home!