DIY Mixer Repair

A blender is an integral element of every kitchen, which is able to mix, beat, grind everything that only your heart desires. To ensure that it always works perfectly, it is necessary to clean it from time to time, but how do you repair your Brown mixer yourself? To deal with this issue, you must have an idea of ​​the main probable malfunctions of such a technique. This will be discussed in this article.

to contents ↑

Instruments

So that you can disassemble and repair the Brown blender with your own hands, you will need the following tools:

• pliers;
• a narrow, thin knife or a flat and thin screwdriver;
• long and flat screwdriver;
• glue for aircraft modeling or superglue;
• hammer.

to contents ↑

Proper disassembly sequence

To properly disassemble and then repair the “Brown” blender (mixer) and not damage important elements, do everything in accordance with the following algorithm:

• Using pliers, remove the cartridge, also called the nozzle holder.
• Take a narrow and thin knife or a screwdriver, insert this tool between the casing and the case, and then, with a simple hammer blow, knock out the weld.
• Repeat the same action along the housing perimeter until the engine and the casing move freely inside the housing.

Important! Be extremely careful near the clamps - in no case do not repel them. Also, do not use a wide knife or a thick screwdriver, as the entire thin external case can burst.

• After that, drown the clamps and remove the engine.
• Directly, the engine can be pulled along with the control board itself. If this does not happen, use pliers to pull the edge of the board, so that it is quite easy to remove.
• Inside you will see 4 latches of the back cover. Fold these latches in the direction of the arrows, as a result of which the top cover will be in your hands.
• Pass the speed control cover with a screwdriver. Bend all the external clips on the power cable holder from the inside.

Important! Be extremely careful when handling the board because it is fragile enough.

to contents ↑

Basic equipment malfunctions

Malfunctions can occur in any equipment, but due to the fact that not everyone can afford expensive options, quite often on the forums you can find questions about how to properly disassemble the “Brown” blender, what problems it may have.

The device does not rotate

This problem is hidden in the knife speed switch.

The blender does not work well or does not chop

Blender and mixer have an incredibly important role to play. If you choose a blender of insufficient power or insufficient quality type, the work efficiency, of course, will be low.

The device does not respond to the network connection

It is possible that something was stuck inside it, or the engine burned out due to excessive use.

Important! In certain cases, a decrease in voltage across the entire power supply network is similarly affected.

Do not switch modes

Most likely, this is a drive problem or a control system.

The knives are broken

This is the most common problem. Such parts can be purchased in almost every company store.They cannot be repaired in any way, which is why it is necessary to carry out a replacement.

The device does not turn on

In the event that the gearbox turns out to be faulty, the device, as a rule, simply does not turn on - it is extremely difficult to carry out such repairs with your own hands. Engine Replacement Instructions:

1. Disassemble your device according to the scheme described above.
2. Be sure to read the recommendations from the manufacturer, as well as the technical parameters of this device.
3. Check the power button and the power button, as well as the lock - it is quite possible that the problem lies specifically in it. If you hear a buzz when you turn on the blender in the mains, then you need to squeeze the contacts, and then test them with a multimeter. In special cases, they do not have the ability to close when turned on.
4. You can buy a separate engine in specialized stores, but such spare parts can be bought exclusively for expensive models or for Kenwood HBM, Polaris PHB, Gastrorag food processors.
5. Install the new engine in place of the old one, assemble, and then check the entire system.

to contents ↑

Is it possible to repair blenders of other brands?

Dismantling the Saturn, Bork and Vitek hand blenders is not possible because their design is molded plastic, and a plastic ring is soldered into the base and cannot be removed.

Therefore, you have only 2 options to solve this problem if the device has a problem:

1. Buy a new blender. Because it is impossible to repair the device without damaging the case.
2. Solder directly the panel. To connect the housing, plastic soldering technologies are used, as a result of which disassembly can be carried out using high-temperature technology. Carefully cut the case and insert several small needles or metal plates into the cut. Heat them up and then remove the molten plastic. After you have completed the repair, the plastic can be glued again.

Important! Directly in the housing itself is the working part of the blender, and specifically: the motor, spindle and control unit. This block is a circuit that helps to configure all modes and functions. After disassembling, you can replace all the necessary spare parts with workers or clean the contacts of your device.

to contents ↑

Stock footage

In fact, any mixer or blender does not have such a complicated device that it was impossible to repair it. But if the case is made non-separable, and such a model is quite cheap, it makes sense not to waste time on such work, but simply buy a new device.