What to do if the door creaks in the room

Doors are the face of the house. They set the aesthetics of the interior, provide quality ventilation, lighting, and become a barrier against dust and noise from the outside world. Everything can creak - floor, ceiling, chair, table, refrigerator door. By the way, the creak of the latter always unbalances, especially losing weight people. It annoys many when the door creaks in the room. What to do in such a situation, you can find out by reading the advice of experts.

Squeak Reasons

You need to get rid of extraneous sounds as soon as possible, until the creak is crazy. It is not difficult to understand what to do to prevent the door from creaking, but first you need to figure out why the problem arose. Masters distinguish the following reasons:

• poor installation;
• lack of lubrication;
• lack of balls;
• high humidity;
• poor lining;
• faulty elements;
• unreliable hinges;
• poor web adjustment.

The easiest way to get rid of a creak is to lubricate the door. To do this, you need to choose the right materials.

Lubricants

Usually, creaking is a fairly common problem, and its elimination does not take much time. But for this you need to know the source.

If this is the front door, then most likely it is subject to a drop in temperature, especially in the off-season. Graphite powder will perfectly save the landlord and neighbors on the landing from an unpleasant sound.

Masters note that the creaking occurs due to the friction of the hinges against each other (a common occurrence on a wooden door). Over time, the grease between the loops is erased, so the canvas begins to “sing”. In such cases, you should know what to do if a wooden door creaks. The most popular grease recovery products:

• Solidol.
• Chiatim.
• Diesel oil
• Spindle oil.
• Oil for cars. Any engine oil not only eliminates the creaking of door hinges, but also prevents the formation of rust.
• Silicone
• Aerosol lubricants. Multi-purpose greases (e.g. WD-40) are special products.

The universal means of aerosol WD will help to get rid of the problem. Drivers always have this spray can. The basis of the tool is white spirit. In parallel, it removes excess moisture from the surface, and the oil contained in it fills the space.

Such mixtures are sold in the form of oil or spray, they are multifunctional. With their help, you can eliminate internal pollution, creaks, rust. Aerosols form a protective layer that prevents rust.

For good lubrication, it is advisable to remove the door from the hinges. It should be lifted with any solid tool. A crowbar or ax is suitable, which must be placed under the end of the door. Then all the details are put on the door frame, and the door leaf is carefully lubricated with a special tool to eliminate an unpleasant creak.

As a home “first-aid kit”, you can use other lubricants. Their list is not so wide:

• vegetable oil;
• stylus shavings;
• paraffin.

The constant use of improvised tools, as a rule, does not lead to a good result. This is most likely an ambulance "doorway" that will fix the problem for several hours. It is better to spend them properly, see where the source of the problem is and how to deal with it.

Quick ways to eliminate squeaking often exacerbate the problem.For example, oil and petroleum jelly lead to contamination and adherence to dirt, and also cause corrosion and rust. In addition, they help drown out the creaking of loops only until they are dry.

It is worth noting that when the loops are worn out, they simply cannot be lubricated. If possible, they are best replaced.

If there are no special products or if the oil runs out, then you can use liquid soap or any other viscous product.

Other factors

Sometimes creaking occurs as a result of the displacement of the walls. After repair, the exposed doors will be clearly beaten off in level. After a certain time, if you attach a level to them, the bubble will shift to either side. If the door was installed by specialists, most likely they could mark such a problem, but as often happens during repairs, they try to quickly eliminate and forget the difficulties. But when the time comes, these problems begin to arise in different forms, including in the creak. In this case, you need to know what to do if the interior doors creak.

When the question is that the door has shifted due to the wall in the apartment, you can bend the loop. This will remove the effect of independent opening or closing, and for some period the squeaking will stop. Over time, the loops will slip and begin to creak anyway.

The most unpleasant situation is the occurrence of a squeak due to a cracked door jamb. It’s difficult to spot a defect because it can appear anywhere. The first thing to do is try to find exactly where the problem is (usually a small crack). This place can be filled with either not too thick oil (replaces the seal), or with ordinary shampoo. This is a simple method, but, unfortunately, not always effective. If the desired effect is not achieved, it is necessary to turn to a more radical method - the creation of additional fixation.

When the wooden door creaks, it is again necessary to determine the source. The reason may be increased humidity in the room, especially often this is observed during the off-season. By the way, it was at this time that wooden doors were prone to swelling, as they absorb excess moisture. Because of this, the canvas increases in volume. In this situation, only minimizing moisture in the housing will help get rid of the creak.

Squeak also develops with improper or weak fixation of loops. They seem to begin to "hang out". If you attach an ax or a mount under the door and lift the canvas a few centimeters, the loops will be unloaded, so the creak will go away. Solving the problem will help the replacement of fasteners, fastening screws or screws with a larger diameter.

Problem Detection Methods

In order to know exactly where the door in the room creaks and what to do with it, where the friction occurs, you can use a carbon copy. To do this, attach carbon paper to the end of the door leaf and cover it. In the place of friction on the door frame will remain stripes. Also, chalk is suitable for identifying a problem area.

The reason may be the end. It is enough to remove a little wood from the place of contact with a plane or a rasp. The cleaned area must be treated and sanded with sandpaper.

If interior doors creak, then you can determine the reason for their creaking by the method of exclusion. Common causes may include:

• box breakage;
• hardware breakdown;
• web breakage;
• chip door;
• crack of the canvas or box;
• box displacement (even a new sample may be damaged).

Simple breakdowns also become a cause of “melodiousness,” in particular, problems with fittings (a handle, a lock, etc.).

If you can’t cope with the creak on your own, then it is better to contact the master who installed the door leaf. Perhaps, during the installation, he could talk about problems with the walls or the door, which was safely forgotten. Incorrect hinges during installation are common.If this is the reason, then the creak will appear immediately after the installation of the door and the start of its use.

As for the front or outer iron door hinges, welded before installing the door, it is hardly possible to do anything yourself. The creaking of a metal door can be cleaned with engine oil only if it is the friction of the parts of the hinge.

A metal-plastic door can also “sing” from time to time. To eliminate the creak in it, you must first eliminate sagging, that is, adjust the upper and lower loops.