How to whiten a bath at home?

One of the most beloved places of a person in the apartment is the bathroom, but strangely enough, the idea of ​​cleaning the bath itself is usually visited by people very rarely. When the time comes for general cleaning, among other questions, how to clean one or another in the house, at one point your eyes accidentally fall on the bath bowl and you think about how to bleach the bath at home so that it does not look like it is covered with cracks land after a drought. To help you and your aesthetic impulse, in this article we will talk about how to clean and bleach a new bath so as not to damage the coating, as well as how to bleach a cast-iron bath.

to contents ↑

Types of bathtubs

Oddly enough, but often new bathtubs get dirty and acquire a swollen coating faster than old cast-iron. What can I say, Soviet manufacturers really knew how to produce a quality product. But modern bowls are much more convenient, have a variety in design and shape, easier, so replacing bulky plumbing is relevant today.

So, for starters, the types of bathtubs, there are only four of them:

• cast iron;
• metal;
• plastic;
• coated with acrylic.

Here we will pay attention to cast-iron and acrylic bowls, as these bathtubs are used most often. What to consider here:

1. The peculiarity of the cast-iron bath is that it holds the temperature perfectly, but quickly accumulates plaque. This plumbing is easier to clean, it can be subjected to global rough cleaning and nothing bad will happen if you approach wisely.
2. Acrylic retains an elegant appearance for a long time, but the coating does not tolerate such harsh treatment, it must be handled extremely gently.

Note: You can use the same bleaching methods for a plastic bath, which is suitable for acrylic, and for metal - those that are for cast iron.

to contents ↑

Prevention

Special attention deserves the care of the bathroom. Despite the fact that this container is often wet, when you are not using the bowl, make sure that it is completely dry. Surely, you often noticed rusty smudges at the bottom of the bath when there are puddles of water left there.

Always keep a dry, clean cloth in close proximity to wipe the bowl after using it for its intended purpose. This simple action will be enough to make you less likely to wonder what to whiten the bath at home.

Important! Make sure that your plumbing is in order and that no water drips or flows from the faucet - in addition to saving the bath, you will also save on water consumption.

to contents ↑

How to whiten an old bath at home?

As mentioned above, old containers are sometimes better than new ones, but after a while, even with the most clean housewife, the old bath acquires a dark coating. This is an action of time and nothing can be done about it. How to whiten an old bath at home is not an easy task. Enamel has already undergone significant changes and has lost those qualities that were characteristic of her when she was new.

To date, there are several effective ways to bring the coating in proper form - both with the help of chemistry and folk remedies. We will tell you about them now.

Heavy artillery

Many do not “bother” and use such tools as “Domestos” and others - those that are designed to clean the toilet. Particularly effective means for cleaning gas stoves noted users who use them to clean the bowl for bathing.

Important! You can try this option as an ambulance, because these are very strong substances that will remove everything that has accumulated on it from the coating. But since usually such household chemicals are very aggressive, with frequent use, enamel can be destroyed much faster. Note this for yourself and for regular use choose more gentle means.

More gentle but effective ways

If you decide to act more correctly, we offer you such effective solutions. They will require a little more effort from you, but you definitely will not damage your plumbing.

You will need:

• ordinary dishwashing sponge with a hard lining on the other hand;
• iron bristle brush;
• cleaning powder;
• chlorine bleach (whiteness);
• oxalic acid;
• soda;
• vinegar;
• anti rust agents.

First way:

1. Wet the bowl.
2. Spread the detergent over the surface.
3. Wait about an hour.
4. Clean the container with a wire brush, most thoroughly where it is dirtier.
5. Wash with running water.

The second way:

1. Dilute soda with water to a slurry condition.
2. Apply the resulting thicken to the bath.
3. Leave on for 5-10 minutes.
4. Mix bleach and vinegar in a 1 to 1 ratio.
5. Apply to bath surface over soda.
6. Leave for 2 hours.
7. Rinse well with clean water.

The third way:

1. Rub the container well with a brush.
2. Wash away any dirt and rust with water.
3. Apply oxalic acid diluted with water in the form of slurry to the entire surface where it was previously brushed.
4. Leave it all for 20-30 minutes.
5. Rinse again with water.

The fourth way (for the lazy):

1. Pour water into the container to the brim.
2. Pour 3-4 bottles of white there.
3. Leave it overnight.
4. Release water in the morning and rinse very thoroughly with running water, while wiping the surface with a sponge.

Note: After all the procedures, do not forget about the mixers and treat them with rust and limescale. Work with gloves.

to contents ↑

How to bleach a new cast-iron or metal bath with enamel

The new bath has not yet had time to come in very poor condition and you can use milder methods. How to bleach a cast-iron bath to maintain its novelty and freshness, you will learn below.

You will need:

• ordinary dishwashing sponge with a stiffer lining on the other hand;
• soft brush;
• plumbing cleaner;
• ammonia;
• washing powder.

First way:

1. Put very (very!) Hot water into the bowl.
2. Leave on for 15 minutes.
3. Drain the water.
4. Wipe the enamel with ammonia using a sponge.
5. Leave the alcohol on the surface for another 20-30 minutes.
6. Apply washing powder and rub with a soft brush.
7. Rinse with clean water.

The second way (for the lazy):

1. Wet the bath with water.
2. Apply a special cleaner for plumbing.
3. Rub with a sponge.
4. Rinse with running water.

Note: Do not use chemistry frequently. No matter how they write on the bottle, in any case, it can shorten the enamel's life faster than using ordinary kitchen products such as soda and vinegar.

to contents ↑

How to tidy an acrylic bathtub?

How to whiten a bath at home, if it is covered with acrylic? Any gentle means that are just invented for this purpose. Do not use what is written above in any case. Acrylic container is not an expensive pleasure, it is not worth spoiling it irrevocably in the name of purity.

The easiest and most effective way to whiten and clean the acrylic container will be the use of special products specifically for those bathtubs that you can buy at any household chemical store. And of the popular methods, again, there is only one - to clean the bath with a sponge with dishwashing liquid.

If you need to clean the bath more globally, buy a special repair complex for cleaning and polishing an acrylic bowl, which is usually sold in the shops “Everything for repair”.

to contents ↑

Stock footage

Are you sure that bleaching the bath at home is easy? And now, arm yourself with the necessary devices, means, and act! Let your bath be perfectly clean, and you are pleased that you were able to quickly restore it with improvised means in 1 day.