How to clean a fur coat from a beaver at home?

Each owner of fur products knows that their long operation is possible only if care is taken correctly. Of course, you can give your favorite fur coat for dry cleaning, but suddenly there will be a collision there? There are no options here: you need to know how to clean a fur coat from a beaver at home. This is not so difficult - just follow the rules. We will tell you about them in this article.

to contents ↑

What you need to know about fur coats?

Fur products “live” long enough, but many owners successfully shorten their useful life. For instance:

• a mink coat will last up to one and a half decades;
• Arctic fox - up to ten;
• rabbit - up to five;
• beaver is a record holder; it can be left unchanged for twenty-twenty-five years.

And what leads to the fact that after one season the product looks, to put it mildly, completely unattractive? Fur wear is due to:

• Wearing a fur coat under snow and rain;
• Product dusting;
• Incorrect drying mode;
• Contact with wool of small debris;
• Improper care.

Important! Washing fur products is strictly prohibited! Because of this, spoilage of the fur, lining and the original shape of the product occurs.

to contents ↑

Care for fur products - the basic rules:

• Do not use a heating radiator to dry the fur coat. It should dry naturally.
• Also, it is impossible to use an open flame, gas burner or hair dryer for these purposes.
• If dirt, debris and dust are clearly not visible, do not need to be cleaned again.
• Do not use chemicals or detergents for processing.
• You cannot iron fur.
• Cleaning is carried out after each season.
• To store the product, a canvas bag is used, which does not need to be tied up so that air enters it.
• The fur requires constant combing with a special tool.

to contents ↑

Fur coat cleaning

For high-quality cleaning, it is best to contact a dry cleaner, but it is important to know how to clean a beaver fur coat at home. Before proceeding to the procedures, we determine the type of fur.

He can be:

• Full-haired;
• Sheared;
• Plucked out.

Basic recommendations

Of course, in order to maintain a fur coat in order, you need to spend time and energy:

• When wiping the plucked or sheared fur, the procedure is performed against the direction of hair growth.
• With full-haired fur, you need to do the opposite.
• To make the fur fresher or to remove small impurities, the product is shaken and cleaned with a brush previously moistened with purified gasoline.
• Gasoline can be replaced with a solution, which includes one part of water and two - ammonia.
• Then the fur coat is wiped with a dry cloth.
• For a beautiful laying of fur after the procedure, you can use a comb or a metal brush.

Important! You can comb the fur only after it has completely dried. Movements should be non-aggressive and smooth.

Shampoo and Glycerin

How to clean a fur coat from a beaver so that it becomes fresh and shiny again? To do this, you can use glycerin:

1. The cotton pad is wetted in this tool and is used to process the product.
2. For better treatment, from stains to glycerol, a mixture of warm water (1 tbsp.) And shampoo (15-20 ml) can be applied to the fur. FROM
3. The mixture is applied with a sponge, which should not be too wet.

Hot sand

According to some experts, beaver coats cannot be cleaned with wet methods.For this, an unusual alternative is recommended - use sand:

1. Sand is washed and dried in the required amount.
2. He pours himself into a deep frying pan and heats up. The temperature should not be too high, as the skin can be deformed.
3. The fur coat is laid out on a flat plane, all buttons are fastened.
4. Warm sand is evenly poured on the contaminated areas and slightly rubbed by hand.
5. If the first attempt does not remove contaminants, the procedure must be repeated.

to contents ↑

White fur cleaning

The look of a white beaver coat is very attractive, but only if it is clean. To remove stains and greasy areas, you can use several tools.

Hydrogen peroxide:

1. Hydrogen peroxide (1 tbsp. L.) Is dissolved in warm water (1 l.).
2. A cotton pad or clean rag is wetted into the solution and used to process the product. You cannot press hard during processing.
3. The fur coat is dried, then combed.

Potato starch:

1. The product is laid out on a flat surface, all buttons are fastened.
2. Starch is poured on contaminated sites, you can rub it a little.
3. The fur coat is well shaken to remove starch residues.
4. If all the starch is not removed, the fur coat can be carefully knocked out.

to contents ↑

Stock footage

A fur coat is the clothes that every woman dreams of. If you take care of her properly, she will delight not one or two winters, but decades. For help, you can turn to specialists, or you can do everything yourself, using the tools that are in every home. We told you about them in this article.